Trusted by Diverse Organisations Across Industries
It Seems Fine Until Everything Stops Working
Do you know if the cabling in your building was installed by someone qualified? Being a licenced electrician in Australia is not enough on its own. Network Cabling requires a separate qualification and registration, the same way an electrician needs an additional air conditioning qualification before they can install a split system.
Here’s how it plays out. Six months later, the connection drops. The cabling fails. There's no test documentation, no compliance record, and no warranty. And you're paying to have the whole job done again.
This time by someone who knows what they're doing. Hopefully.
Built to Last Where Mechanical Connectors Fall Short
End-to-end fibre design, installation and documentation managed by one team, so nothing gets handed off, glossed over or left for someone else to fix.
From Design to Live Network
Fourier designs the fibre solution, coordinates earthworks, hauls the fibre and fits out the building. All of it under one project, managed by one team. No coordination between separate designers, earthworks crews and installers.
Compliant, Documented, Warranted
Every installation meets ACMA requirements. At handover, you’ll receive full test documentation and compliance records. The basis for a warranty claim if anything goes wrong. Most unregistered installations don’t come with this. And that’s a red flag.
Fusion Spliced As Standard
Fusion splicing melts glass fibres together into a permanent, low-loss join built to last. Reliable, low-loss and built to last. Mechanical connectors are cheaper but far more likely to fail in remote environments. Fourier uses fusion splicing only.
Fully Connected
End-to-end means end-to-end. Internal Cat6 and structured cabling is included, so every work point, access point and device connection is in place before Fourier leaves. No second contractor. No gap.
One Project Manager
Cabling projects involve multiple trades. Fourier project manages all of it, one point of contact from start to finish. Coordinating subcontractors and managing the timeline so your organisation doesn’t have to.
Delivering Results, One Partnership at a Time
Your Project, Documented & Accessible
Cabling and fibre projects generate more paperwork than most organisations expect: design specs, test results, compliance forms, site records. Our live documentation platform is where all of it lives, organised and accessible from the moment your project is handed over.
Track project milestones, access your ACMA-compliant test documentation and TCOQ forms, and retrieve installation records whenever you need them. For organisations managing assets across multiple buildings or sites, having accurate infrastructure documentation on hand is essential whether for warranty claims, future upgrades or audits.
Let's Get Your Building
Connected the Right Way
Whether it's a new building, a new site or ageing cabling that's causing problems, get in touch to discuss your project. We'll design a compliant, warranted solution from the ground up.
Get in Touch
Working with Industry Leaders
FAQs
Can a local electrician install my network cabling, or does it need to be a specialist?
A licenced electrician can run cable, but network cabling requires a registered cabler with specific ACMA qualifications, not just an electrical licence.
In Australia, telecommunications cabling must be installed by a registered cabler. An electrician without that additional qualification and registration is not permitted to carry out this work. And any work they would complete won’t come with the compliance documentation or warranty coverage a proper installation provides. Fourier’s installations are carried out by registered cablers and fully documented at handover.
What is the difference between fusion splicing and mechanical connectors for fibre cabling?
Fusion splicing permanently joins two fibre strands by melting them together. This is more reliable and longer lasting than mechanical connectors, which clip fibres together and are more prone to failure over time.
Mechanical connectors use a gel-filled sleeve to align two fibre ends. This can be quicker and cheaper to install, but any movement, moisture or temperature change can cause misalignment and signal loss. In remote environments where re-attending a site is costly, that’s a serious problem. Fusion splicing creates a permanent glass-to-glass join with no moving parts. Fourier uses fusion splicing on every installation.
What documentation do I receive at the end of a network cabling installation?
At handover, Fourier provides full ACMA compliance documentation, including TCOQ forms and complete test results for every cable run. This gives you the basis for a warranty claim for the life of the installation.
TCOQ forms confirm the work was carried out by a registered cabler in accordance with ACMA requirements. Test results confirm every cable run meets the required performance standard. Without both, you have no warranty. Fourier provides both as standard on every job.
How do I know if a cabling installation is properly warranted and compliant with Australian standards?
A properly warranted installation comes with ACMA compliance documentation, test results for every cable run and confirmation that the work was carried out by a registered cabler.
If you have an existing installation and you’re not sure whether it’s compliant. Fourier can assess it and advise. If the documentation doesn’t exist or the work wasn't done by a registered cabler, the installation may not be warranted. Fourier can remediate non-compliant installations and provide proper documentation going forward.
Do you manage the earthworks as well as the network cabling installation?
Yes. Fourier coordinates all earthworks as part of the cabling project, including pits, pipes and conduit, as well as the fibre installation and internal building fit-out.
Most cabling providers install the cable but leave the earthworks to someone else. This means you would be coordinating between multiple contractors on a job that should be seamless. Fourier manages the whole scope from design through to a live network.
Can you connect multiple buildings including internal fit-out as a single cabling project?
Yes. Fourier delivers multi-building fibre projects as a single end-to-end project, including internal Cat6 fit-out at each building.
Fourier handles fibre between buildings, earthworks coordination and internal Cat6 fit-out at every destination. All as one project, with one point of contact and one set of documentation at handover.
Your Communications Infrastructure, Built & Managed as One
From the fibre in the ground to the network it powers, Fourier manages every layer so your connectivity performs the way it was designed to.
Business Internet Services
The foundation of everything you do. Reliable, business-grade internet across fibre, NBN, fixed wireless, 4G/5G and satellite. With the right technology recommended for your location, not the easiest one to sell.
View MoreBusiness Phone Systems
Modern phone systems that work the way your business does. Whether you’re in the office, on the road, or across multiple sites, stay connected with a solution built around your team.
View MoreMobile Services
Keep your people connected wherever the work takes them. Business mobile plans managed under one roof, alongside the rest of your connectivity. No extra accounts, no separate support lines.
View MoreManaged Network Solutions
Your internet connection is only as good as the network it runs on. Switches, Wi-Fi, gateways and more designed, installed and managed so you don’t have to think about it.
View MoreManaged CCTV
Protect your people, assets and premises with a professionally managed CCTV solution. From design and installation through to ongoing monitoring and support. Security you can rely on without the admin.
View MoreP2P Wireless Bridging
For locations where fibre doesn’t reach and fixed wireless isn’t an option. High speed, secure connectivity across distances that would otherwise be cost-prohibitive to connect
View MoreReady to Have Cabling You Can Actually Stand Behind?
Tell us about your project, and Fourier will walk you through what a compliant, warranted installation looks like for you.